How To Repair Large Holes In Mobile Home Walls

Download Article

When you lot have a big hole in your wall, information technology'southward easy to patch it upwardly and so you can paint over it. Use a wall repair patch to hands cover upwardly holes upwards to half-dozen in (15 cm) in diameter. Cutting larger holes into a square or rectangle, and then create a patch out of drywall and attach information technology to the within of the hole. Cover up either type of patch with articulation compound and sand it to blend it into the surrounding wall.

1
Cut abroad and remove any loose droppings and jagged paper edges from the hole. Pull off any dangling pieces of drywall and plaster. Use a utility pocketknife to cut forth the edges and remove any jagged pieces of drywall paper.^[1]
- The goal is to clean the pigsty up plenty that the wall repair patch will sit flat on superlative of it with no loose debris or ragged newspaper edges pushing confronting information technology or interfering with the agglutinative.
- This method works for holes that are upward to about 6 in (15 cm) in diameter. Wall patches come up in sizes up to 7–8 in (18–20 cm) in diameter, and the patch needs to be slightly bigger than the pigsty to attach to the wall effectually it.
2
Create a repair patch that is about ane in (2.five cm) bigger than the hole. Use precipitous pair of scissors to cut a wall repair patch and then that information technology is approximately 1 in (ii.5 cm) taller and 1 in (2.5 cm) wider than the hole in the wall. This will let it to adhere firmly to the intact wall surrounding the hole.^[two] ^[iii]
- You lot can purchase wall repair patches in dissimilar sizes, so you can also just purchase ane that is the right size.
- Wall repair patches are made of a mesh material that is able to back up spackling on pinnacle of it.
Advertizing
3
Pare the bankroll off the patch and stick information technology over the hole. Remove the lining from the agglutinative on the dorsum of the patch. Center information technology over the hole and printing down firmly effectually all the sides to stick it to the wall.^[4]
- You don't need to wait for the patch to dry on the wall, the adhesive patch will be sealed and ready to cover up every bit soon as you stick it on.
four
Apply a thin layer of joint compound to completely cover the patch. Apply a putty pocketknife to spread a layer of joint compound over the entire patch and so you tin't encounter the mesh anymore.^[v] Overlap the coat onto the surrounding wall by nigh 1 in (ii.5 cm).^[6]
- Overlapping the articulation compound onto the surrounding wall will brand it easier to alloy in so the patch isn't noticeable.
Tip: Joint compound is besides known every bit drywall mud or just mud.
5

Permit the joint compound dry for 24 hours. Await until the compound is completely dry out before sanding. This usually takes upwards to 24 hours, only drying times vary depending on the temperature and humidity.^[7]
6
Sand the patch with fine-dust sandpaper until it is polish. Attach a piece of 120- to 150-grit sandpaper to a sanding block or just sand by hand. Lightly sand the unabridged patch downward until it is smooth and blends in with the surrounding wall.^[eight]
- Don't sand as well hard or you might betrayal the mesh patch below the compound. Just focus on smoothing out any rough spots and blending information technology in with the wall.
7
Repeat the process for a second coat of joint chemical compound. Use some other thin layer of joint chemical compound over the patch and the surrounding wall. Let it dry for 24 hours, then sand information technology down with fine-grit sandpaper until it is smooth and blends in with the wall.^[nine]
- If you want to make the joint chemical compound textured, you tin dab it with a sponge while it is still moisture or use a textured paint roller to use a concluding thin layer of watered-down compound.
- If you're ready to paint the wall, use a h2o-based primer to prime the patch before applying wall paint.
Advertisement

i
Cut the hole into a bully foursquare or rectangle. Employ a utility pocketknife or drywall saw to cutting the jagged pigsty into a square or rectangle with straight edges.^[10] This will allow y'all to create a precisely-shaped patch for the drywall and install information technology hands.^[eleven]
- This method works for holes that are bigger than 6 in (fifteen cm) in diameter.
ii
Create a patch out of drywall that is 2 in (5.i cm) taller than the hole. Cut a piece of drywall to the same width as, or but slightly wider, than the hole but a full 2 in (5.1 cm) taller. The extra pinnacle will let y'all to attach it to the within of the pigsty with adhesive.^[12]
- You can purchase modest pieces of drywall for patching that are 2 ft (0.61 thousand) in bore.
Tip: If you don't have a bit piece of drywall to make a patch out of, you lot could utilize a ¹⁄_two in (one.3 cm)-thick piece of scrap wood instead.
3
Put a screw through the eye of the patch to make a handle. Twist or push button a one.5 in (iii.8 cm) or 2 in (5.one cm) drywall screw through the middle of the drywall patch you made so there is nonetheless plenty sticking upwardly for you to grab onto. This volition allow you to hold it against the inside of the hole while you permit the adhesive dry out.^[thirteen]
- If you don't have a drywall spiral you can use a forest screw instead.
4
Utilize construction adhesive to the bottom and top edges of the patch. Put a zig-zag of structure adhesive along the top i in (2.five cm) of the patch. Practice the same for the bottom 1 in (2.5 cm).^[xiv]
- For example, you tin can utilise a construction adhesive like liquid nails.
five
Insert the patch into the hole and apply the spiral to agree it in place while it sets. Option up the patch by the screw and tilt information technology until y'all can insert it into the pigsty. Straighten information technology out so it is oriented correctly and pull it towards the inside of the wall so the adhesive makes contact. Hold it in place for about fifteen minutes until the adhesive has dried enough to hold it in identify.^[xv]
- You tin either button the screw through the patch into the wall void once information technology has dried or unscrew it and pull information technology out.
half-dozen
Let the adhesive cure for upwards to 24 hours before proceeding. Refer to the manufacturer's instructions for the adhesive you used to get the exact drying time. Exit information technology to cure in place at least overnight and up to 24 hours.
- This will ensure that the patch is secured strongly in place and will be able to support the weight of articulation chemical compound.
7
Put a thick layer of joint chemical compound on acme of the patch to make full it in. Use a putty knife to apply joint chemical compound over the patch until the pigsty is filled to the level of the wall. Smooth out the edges and then the chemical compound overlaps onto the wall by near i in (2.5 cm).^[16]
- Use the widest putty pocketknife you lot have to polish out the edges more hands.
viii
Let the first layer of joint compound dry out for 24 hours. Exit the patch to dry for about 24 hours so it is totally cured before sanding. This is especially of import since this layer is relatively thick and it volition have longer to dry than a thin layer of articulation compound.^[17]
- If you lot don't permit the joint compound dry completely, there will be moisture trapped inside that can crusade the patch to autumn apart.
9
Sand the joint compound smooth after it is dry. Apply 120- to 150-grit sandpaper to smooth out the first layer of joint compound. Sand by hand or using a sanding block.^[xviii]
- Merely endeavor to get rid of whatever rough patches and blend the edges into the surrounding wall. You will be repeating the process, and then don't worry about getting information technology perfect.
10
Use 1-2 additional thin layers of articulation chemical compound to alloy the patch in. Apply a putty pocketknife to apply some other thin coat over the patch and the surrounding 1 in (2.five cm) or so of the wall. Let it dry overnight, then sand it down with 120- to 150-grit sandpaper to smooth it out and blend it in with the wall. Repeat the steps for another layer if yous want to alloy it in even more.^[xix]
- If you need to make the joint chemical compound textured to match the balance of the wall, use a textured roller to apply watered-down compound as the terminal layer or dab the final layer with a sponge while it is still wet.
- Remember to let the final coat dry for at least 24 hours before priming the patch and painting the wall.
Ad

Ask a Question

200 characters left

Include your e-mail address to become a message when this question is answered.

Submit

Things Yous'll Need

Wall repair patch
Scissors
Utility knife
Putty knife
Joint chemical compound
Sanding cake (optional)
120- to 150-grit sandpaper

Utility knife or drywall saw
Slice of drywall
Putty knife
Joint compound
Sanding block (optional)
120- to 150-grit sandpaper
Drywall spiral or wood spiral
Construction adhesive

About This Article

Thanks to all authors for creating a page that has been read 17,185 times.

Did this article help you?